Accessories and Components

This brass tee is perfect for pressure tank installations where the tank has a 1" Female connection.  For example, Well-X-Trol WX-201, WX-202, WX-203 or PumpPro PP-202, PP-203, PP-205.

Tank connection: 1" MPT
The side ports are 1" MPT / 3/4" FMPT
The top... more details

This brass/copper tee is perfect for pressure tank installations where the tank has a 1 1/4" Female connection.  For example, Well-X-Trol WX-205, WX-250, WX-251, WX-252, WX-255, WX-302, WX-350 or PumpPro PP-250, PP-251, PP-252, PP-302, PP-350.

Tank connection: 1 1/4" MPTmore details

This brass tee is perfect for pressure tank installations where the tank has a 1" Male connection.  For example, WellMate WM-6, WM-9, WM-12

Tank connection: 1" FMPT
The side ports are 1" MPT / 3/4" FMPT
The top ports are 1/4" FMPT (for pressure swit... more details

This brass tee is perfect for pressure tank installations where the tank has a 1 1/4" Male connection.  For example, WellMate WM-14, WM-25, WM-35

Tank connection: 1 1/4" FMPT
The side ports are 1 1/4" MPT / 1" FMPT
The top ports are 1/4" FMPT (for p... more details

Pitless adapters are underground discharge units that mount into the water well casing down below the frost level. The piece that goes through the well casing secures with a rubber washer and nut on the outside of the casing. The inside of that unit is a receiver for the piece that comes up from you... more details

Pitless adapters are underground discharge units that mount into the water well casing down below the frost level. The piece that goes through the well casing secures with a rubber washer and nut on the outside of the casing. The inside of that unit is a receiver for the piece that comes up from you... more details

1" Check Valve

 

 

 

 

 

 

3/4" Ball Valve

1" Brass Ball Valve

1 1/2" Ball Valve

 

Cast Brass Pipe Threaded Fitting
Union Fitting Size: 1" X 1"
End Connections: FNPT x FNPT

1/2" Pressure Relief Valve, protects against excessive pressure, preset at 100psi

3/4" Pressure Relief Valve, protects against excessive pressure, preset at 100psi.

Series N55B-M1 Water Pressure Reducing Valves are designed to reduce incoming water pressure to a sensible level to protect plumbing system components and reduce water consumption. This series is suitable for water supply pressures up to 400psi (27.6 bar) and may be adjusted from 25 to 75psi (172 &n... more details

Series N55B-M1 Water Pressure Reducing Valves are designed to reduce incoming water pressure to a sensible level to protect plumbing system components and reduce water consumption. This series is suitable for water supply pressures up to 400psi (27.6 bar) and may be adjusted from 25 to 75psi (172 &n... more details

The industry standard for controlling electrically driven water pumps. 
For optimal efficiency, set your pressure tank air charge 2 PSI below the cut-in pressure.  (18 PSI)

The industry standard for controlling electrically driven water pumps.  Low Pressure Shut-Off operates at approximately 10 PSIG below cut-in and will turn off the pump.
For optimal efficiency, set your pressure tank air charge 2 PSI below the cut-in pressure.  (28 PSI)

The industry standard for controlling electrically driven water pumps.
For optimal efficiency, set your pressure tank air charge 2 PSI below the cut-in pressure.  (28 PSI)

The industry standard for controlling electrically driven water pumps.
For optimal efficiency, set your pressure tank air charge 2 PSI below the cut-in pressure.  (38 PSI)

Type-G 50/70 PSI Heavy Duty, High Pressure Switch Controls electrically driven water pumps and air compressors.
For optimal efficiency, set your pressure tank air charge 2 PSI below the cut-in pressure.  (48 PSI)

Type-G 60/80 PSI High Pressure Switch Controls electrically driven water pumps and air compressors.
For optimal efficiency, set your pressure tank air charge 2 PSI below the cut-in pressure.  (58 PSI)

The Model 233-P single-phase Pump Saver Plus is a pump monitor designed to protect single-phase pumps from dry-well, dead-head, jammed impeller, rapid cycle and overvoltage and undervoltage conditions. The Pump Saver Plus Model 233-P protects 230 volt, 2 or 3 wire, 1/3 to 1.5 hp pumps.

A ... more details

Basic coyotes protect pumps and motors from running dry and from low voltage.  They trip in a fraction of a second on sensing a lack of fluid and restart the pump at any interval dialed on the timer from 5 minutes to 5 hours.  Sensitivity to running dry is adjustable and set at installatio... more details

Basic coyotes protect pumps and motors from running dry and from low voltage.  They trip in a fraction of a second on sensing a lack of fluid and restart the pump at any interval dialed on the timer from 5 minutes to 5 hours.  Sensitivity to running dry is adjustable and set at installatio... more details

Super coyotes protect pumps and motors from running dry, low and high voltage, rapid cycling, and excessive current draw.  They trip in a fraction of a second on sensing a lack of fluid, and restart the pump at any interval dialed on the timer from 1 minute to 12 hours.  Sensitivity to run... more details

Super coyotes protect pumps and motors from running dry, low and high voltage, rapid cycling, and excessive current draw.  They trip in a fraction of a second on sensing a lack of fluid, and restart the pump at any interval dialed on the timer from 1 minute to 12 hours.  Sensitivity to run... more details

PUMP PROTECTION AT ITS BEST

For Franklin 2 & 3-wire single-phase motors, 1/3 to 1.5 hp

The facts are clear and so are the choices. Franklin Electric’s Pumptec family provides the high performance pump protection you need deep down in the well. Designed to monitor motor... more details

PUMP PROTECTION AT ITS BEST

Protects all brands and types of pumps 230V, 1/2 through 5 HP.   The facts are clear and so are the choices. Franklin Electric’s Pumptec family provides the high performance pump protection you need deep down in the well. Designed to monitor... more details

Control Box for 3 Wire, 1/2HP, 115V motors.  Franklin's quick disconnect control box takes time and sweat out of installation and repair. The lid disconnects with a flip of the wrist. To replace the motor controls just snap a new lid in place. As you strip and feed the wire, you don't have to w... more details

Control Box for 3 Wire, 1/2HP, 230V motors.  Franklin's quick disconnect control box takes time and sweat out of installation and repair. The lid disconnects with a flip of the wrist. To replace the motor controls just snap a new lid in place. As you strip and feed the wire, you don't have to w... more details

Control Box for 3 Wire, 3/4HP, 230V motors.  Franklin's quick disconnect control box takes time and sweat out of installation and repair. The lid disconnects with a flip of the wrist. To replace the motor controls just snap a new lid in place. As you strip and feed the wire, you don't have to w... more details

Control Box for 3 Wire, 1HP, 230V motors.  Franklin's quick disconnect control box takes time and sweat out of installation and repair. The lid disconnects with a flip of the wrist. To replace the motor controls just snap a new lid in place. As you strip and feed the wire, you don't have to wra... more details

Control Box for 3 Wire, 1 1/2HP, 230V motors.  Franklin's quick disconnect control box takes time and sweat out of installation and repair. The lid disconnects with a flip of the wrist. To replace the motor controls just snap a new lid in place. As you strip and feed the wire, you don't have to... more details

Control Box for 3 Wire, 2HP, 230V motors.  Franklin's quick disconnect control box takes time and sweat out of installation and repair. The lid disconnects with a flip of the wrist. To replace the motor controls just snap a new lid in place. As you strip and feed the wire, you don't have to wra... more details

Control Box for 3 Wire, 3HP, 230V motors.  Franklin's quick disconnect control box takes time and sweat out of installation and repair. The lid disconnects with a flip of the wrist. To replace the motor controls just snap a new lid in place. As you strip and feed the wire, you don't have to wra... more details

Control Box for 3 Wire, 5HP, 230V motors.  Franklin's quick disconnect control box takes time and sweat out of installation and repair. The lid disconnects with a flip of the wrist. To replace the motor controls just snap a new lid in place. As you strip and feed the wire, you don't have to wra... more details

Fill funnel specifically designed for filtration system re-beds.

One length, cut to size. 

Available in 3 sizes: (You will be asked to choose diameter at checkout.)
1.05" O.D. - Most Common
13/16" O.D.
1 1/4" O.D.

The Eco-Tech DLA-G15 multipurpose standpipe airgap is designed for residential and commercial water treatment equipment and condensate lines that require an airgap discharge to the drain. The DLA-G15 is perfect for applications where rigid Schedule-40 pipe must be plumbed to an approved airgap devic... more details

3/4" Stainless Steel By-Pass valve for control valves.

1" Stainless Steel by-pass valve for most control valves.

1/2" polypropylene backwash line, 50'

Used for connecting two backwash lines to a single discharge line.

Don't let the condensation reach your floor, catch it with a drip pan.

Safely and securely route your backwash lines with these 1/2" snail clips.

Mounting kit for Big Blue housings.

Use this filter wrench to easily loosen Big Blue filter housings when replacing cartridges.

Use this filter wrench to easily loosen Big Clear filter housings when replacing cartridges.

Use this filter wrench to easily loosen Standard Valve-in-Head housings when replacing cartridges.

Big Blue Buna-N replacement O-ring.  The rubber O-ring provides the water-tight seal between the cap and housing, and should be replaced after every cartridge change.

Be sure to lubricate with clean silicone grease and properly seat in the groove below the threads of the housing to a... more details

Standard Buna-N replacement O-ring.  The rubber O-ring provides the water-tight seal between the cap and housing, and should be replaced after every cartridge change.

Be sure to lubricate with clean silicone grease and properly seat in the groove below the threads of the housing to... more details

Universal style fits most booster and jet pumps.   Easily installed on top of tank.   Zinc-plated steel with plastic feet to protect surface of tank.   Hardware included.

Professionally and securely seal your well wire connection splices.

A low priced guide with a snap-in feature for installing the pump cable. Fits 6" wells, tabs can be cut for 4" to 5".  For 1" Poly Pipe.  It is recommended to install for every 25 feet of wire.

A low priced guide with a snap-in feature for installing the pump cable. Fits 6" wells, tabs can be cut for 4" to 5".  For 1 1/4" Poly Pipe.  It is recommended to install for every 25 feet of wire.

Ideal Stainless Steel Hose Clamps for 1" Poly pipe. 

Fits pipe: 1/2" - 1" Diameter

Ideal Stainless Steel Hose Clamps for 1 1/4" Poly pipe. 

Fits pipe: 1 1/4" Diameter

The torque arrestor is used to prevent motor start up torque from thrusting the pump against the side of the well casing. Think of it as a shock absorber for your well system.

Standard Pressure Gauge with a Range 0-100psi and 1/4" NPT

Defend your submersible pump and water system from the abrasive, damaging and costly effects of sand with a Lakos SUB-K Pump Protection Separator. Using controlled centrifugal action, troublesome sand is removed from the water before it enters the pump, reducing wear to impellers and other vital com... more details

Defend your submersible pump and water system from the abrasive, damaging and costly effects of sand with a Lakos SUB-K Pump Protection Separator. Using controlled centrifugal action, troublesome sand is removed from the water before it enters the pump, reducing wear to impellers and other vital com... more details

Defend your submersible pump and water system from the abrasive, damaging and costly effects of sand with a Lakos SUB-K Pump Protection Separator. Using controlled centrifugal action, troublesome sand is removed from the water before it enters the pump, reducing wear to impellers and other vital com... more details

A Pump Screen provides full protection from Sand and other debris that may be in a traditional well. The Pump screen is a must when setting pumps into ponds, lakes or streams.  This protects the pump from moving objects and allows only water to enter the pump chamber.

Cold resistant, flame retardant, electrical tape. 
3/4" x 60' , UL Listed.

6" Cast Iron Well Cap

6" Cast Iron Watertight Well Cap.

The Well Seal prevents surface water from entering the well.

1" Cast Bronze foot valve with plastic perforated strainer.

1 1/4" Cast Bronze foot valve with perforated strainer.